EPSON TM U375P DRIVER FOR WINDOWS

Take-up spool Paper roll 1 pc Ribbon cassette Power switch cover Removing the Protective Materials The printer is protected during shipping by protective materials that must be removed before you turn on the printer. When printing on a single cut sheet that is narrower than the carriage movement range, once the printer has been put in the cut sheet mode and the sheet of paper has been inserted, the following operations should be avoided: This will prevent paper jams. Click a bookmark to instantly jump to its topic. Warnings must be followed carefully to avoid serious bodily injury. If the print toward you, and pull the paper out in the direction as head is not at the center of the printer, bring it to the shown in Figure Unpacking, Removing The Protective Materials Unpacking The illustration below shows the items included for the standard specification printer.

Uploader: Gardagor
Date Added: 8 August 2009
File Size: 59.76 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 27876
Price: Free* [*Free Regsitration Required]

Reference Cl Chapter 4 contains specifications. Comments to this Manuals Your Name.

Service Temporarily Unavailable

Platen Movement Detailed explanations of each of the detection mechanisms are provided in this section. X, Y, and Z Directions: You can change your interface and print column settings by changing the DIP switch settings. The printer does the following when an error occurs: Paper is not loaded by pressing down paper load switch.

CC U357p x 5 When attaching the solenoid, adjust its position so that the space between the lower end of hole Epson tm u375p and the lower end of hole D is within Page 68 Printed in Japan Using the Power Switch Cover You can use the provided power epson tm u375p cover to protect the power switch from accidental or improper operation.

When you turn off the printer power, data sent from the computer is lost. One is to turn the printer off and on u37p5 before installing or removing j375p ribbon cassette, making sure that data sent from the computer epson tm u375p not lost. Are connectors Remove the paper. Epson tm u375p the interface wire broken? Your printer comes with inch-type hexagonal lock screws installed.

Related Driver:  SCR241 PCMCIA SMART CARD READER DRIVERS FOR MAC DOWNLOAD

Warnings must be followed carefully to avoid serious bodily injury. If the print head is overheated, the printer will resume printing when the head has cooled usually within two or three minutes.

Connect the other end of i375p cable to the connector on your computer. Buttons The control panel buttons perform paper feeding and release functions. Page 21 Check the label on the power supply to make sure that the required voltage matches that of your electrical outlet.

Epson TM-U375 Technical Manual

Page 47 If there epson tm u375p no paper jam and the printer has been printing for quite a while, the print head may be overheated. Page 23 or 3 more times Knob 4. Be sure to install the paper roll in the printer to prevent validation paper jams.

This shows whether your printer is working correctly.

Page 45 Epson tm u375p 3 Troubleshooting Troubleshooting If you plan to use an interface cable that requires millimeter-type lock screws, replace the espon screws with the millimeter-type screws by using a hex screwdriver 5 mm. To print the manual completely, please, download it.

EPSON TM-U TECHNICAL MANUAL Pdf Download.

Replacing The Paper Roll 1. Be sure to install the paper roll in the printer, even if you plan to print only on slip paper or on validation paper. At the same time, the microswitch turns on. The cover clicks when it is closed securely. Also avoid areas which are exposed to direct sunlight for long periods of time.

Notes, Cautions, and Warnings Note: Self-test mode switches to normal epson tm u375p. Page 6 Reference Cl Chapter 4 contains specifications. These are mounted on the switch circuit board unit and sensor circuit board set, which is connected to the main circuit board unit via a connector CN8. The lubricants for the printer are chosen based on technical information analysis and tests on various lubricants by G Gear-Ribbon transmission epson tm u375p shaft Epson.

Related Driver:  KYOCERA 1030D DRIVERS FOR WINDOWS DOWNLOAD

There are two ways to replace the ribbon cassette. Make sure that the ribbon is installed between the print head and the ribbon mask without wrinkles or creases, as shown below.

Send the appropriate control commands from the computer to print on validation paper. Click the Find button if you want to search for a particular term. Paper Roll Supply Mechanism Figure Remove the paper epson tm u375p while pulling the release lever toward you, and pull the paper out in the direction of epson tm u375p arrow as shown in the illustration below. Take-up spool Paper roll 1 pc Ribbon cassette Power switch cover Removing the Protective Materials The printer is protected during shipping by protective materials that must be removed before you turn on the printer.

Carriage motor cable assembly Power switch assembly Perform the sub-assembly first to construct each unit from Is the printer recovered Remove the paper.

Cautions must be observed to avoid minor injury to yourself or damage to your epson tm u375p.

Insert the ribbon in the position as shown below, and push the ribbon cassette into the printer until it clicks. The words on the left side of this screen are tmm for all the. About This Manual Setting up and Using El Chapter 1 contains information on unpacking the printer, setting it up, setting the DIP epson tm u375p, and adjusting the paper near end detector.

B Reliability Information Rev. This manual also for: Tool List Table When the printer is connected to an intelligent module, u375o power is supplied by the intelligent module.